If you are attempting laminate flooring installation for first time it may appear a daunting task for you in the beginning but believe me if you spend little time in understanding the procedure about how to install laminate flooring as per the instructions provided by the manufacturer you can do it easily with out any difficulty. You need to have the required tool kit at your dispense and you are ready to go. But before you start, make sure you plan your installation properly, as with any task preparation is the key. Measure your laying area properly; recheck you have right numbers of laminate squares with you; gauge the space to be floored. This little time which you spend in preparing before hand can safe you tremendous amount of time and installation hassles. Decide your substrate or sub floor you are intending to use. Adaptability is the beauty of floating laminate flooring. It can be placed on almost any substrate including wood, concrete or any other existing flooring. Check with your manufacturer about the ideal temperature in which you can install the laminate flooring. You need to leave your laminates at the place of installation for at least 24-48 hours so that they can acclimatize to the conditions. While installing the laminates leave a gap of 5X16'' from the wall. Place wood or plastic spacers to ensure that you lay all squares in proper order and maintain uniform space all along the wall. This space is integral to the installation as it allows for expansion due to temperature changes. Not leaving this space can damage your laminates with any temperature change. If you are installing over a large area provide 3/8'' for expansion joints every 30-40 linear feet. To mask these you can use expansive joint sealant in these intermediary expansion joints. Expansive joint sealant is also used to seal joints between boards. Make sure you clean and dry surfaces thoroughly before applying sealant. When installation is complete allow at least 24 hours for joints to dry and settle on the floor. Then clean the floor to remove any debris and left over mess from the installation. Then thoroughly inspect al joints for evenness.
The Basics Of Installing A Bathtub
You have finally made up your mind to give your bathroom a much-needed face-lift by installing a new bathtub। Sometimes the need for a new bathtub is out of necessity if it is cracked and old or even leaking which will cause damage to your home. At other times, the need for a new bathtub is merely the want of a better design or color, or just a need for a change in décor. No matter the reason, it is vital that you know the steps to take to properly install a bathtub.
The first thing you need to do before you can install your new tub is to make sure you have picked up everything you need. For example, you want to make sure you have measured the tub area, and then choose a bathtub that is just the right size. Buying a tub that is too wide or long will be cause for massive frustration and possible financial issues as well. Make sure you have all the pipes, fittings, screws, nails, and other necessities. Installing a bathtub correctly without all the proper materials is downright impossible. Therefore, the first step in bathtub installation is to ensure you have everything you need to get the job done right. If in doubt, ask for help at your local hardware store.
Then the fun starts. To avoid damage and disaster when installing a bathtub, make sure you turn off the water before you start your project. One of the most common mistakes made by homeowners when replacing their bathtub is failing to turn the water off in the home, before disconnecting the old pipes. This can lead to flooding within the home, floor damage, wall damage, and expensive repairs. In order to avoid this kind of damage, make sure you remember to turn off the water in the home first.
Before installing the new bathtub to its chosen area it is important to make sure that you attach and tighten all the new pipes properly, as well as secure the bathtub supports. Once this is done, you will place the connections for the drain, while making sure that the trap is lower than the drain to enable the tub to drain properly. Then you will be ready to connect the hot and cold water lines to your new bathtub. Once these are secured with the nipple and caps you will then turn the water back on. You should check for any leaks of all drains and pipes and correct any possible problem before finishing with your installation of the tub.
After checking and being positive there are no leaks, finish up with a tub surround. In some cases, these come with a new bathtub, can be purchase separately, or created yourself using tiles or drywall that is water resistant. Installing a bathtub can be an easy project if you know what precautions to take first.
6 Useful Tips To Save On Renovation
So you have decided you want a bit of a challenge in buying your next house। You are going to invest on a fixer-upper home but you still want to save on renovations। Here are a few tips:
1 Ask your contractor for inexpensive materials। Some contractors have left over materials and parts from previous jobs they have handled and you can ask if they you could use those scrap materials in renovating your fixer-upper home। Left over materials aren't all in bad condition and won't hurt your home’s sturdiness and functionality plus they are cheaper than buying new materials at home supply stores।
2. Choose reliable materials. Just because you are saving up on fixing your fixer upper doesn't mean you should go cheap on everything. There are some materials that can be bought cheaply and there are some that are a little bit pricey but worth it. Investing in good quality, sturdy materials that will last you almost a lifetime is the wisest thing. It will save you money in the long run, it will also save you from consuming time and effort fixing things all over again. 3. Take it down yourself. You can demolish some of the parts of your fixer-upper home yourself. The harder and more dangerous parts to be demolished can be done by a contractor. This way you save up on hiring costs.4. Sell reusable materials. While in the process of taking down some parts of your fixer-upper home, there may be some scrap materials that you won’t need but will be very useful for some other people. Scrap wood, metal, fixtures and other things could be sold to other people who, just like yourself are looking forward to saving a great deal of money.5. Save up on architect fees. Naturally you are going to need an architect to map out the design plan for your fixer upper. Hiring an architect usually doesn't come cheap but you can minimize costs by contracting an architect for a one time visit and consultation and the architect will then design the renovation plan for your fixer-upper home. This will cost less rather than hiring your architect for multiple visits and meetings.6. Leave the sink and the toilet. Moving the sink or toilet will cost big bucks because plumbing prices aren't cheap. As much as possible leave the toilet and sink alone.
Subscribe to:
Posts (Atom)
